Top 10 secret 100-105 for IT professionals (11 to 20)
Cause all that matters here is passing the Cisco 100-105 exam. Cause all that you need is a high score of 100-105 Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) exam. The only one thing you need to do is downloading Examcollection 100-105 exam study guides now. We will not let you down with our money-back guarantee.
2021 Mar 100-105 practice exam
Q11. - (Topic 3)
Refer to the exhibit.
The network is converged.After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?
A. 208.149.23.64[110/13] via 190.173.23.10, 00:00:07, FastEthemet0/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, FastEthemet0/0
B. 208.149.23.64[110/1] via 190.172.23.10, 00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10, 00:00:16, FastEthemet0/0
C. 208.149.23.64[110/13] via 190.173.23.10, 00:00:07, Serial1/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, Serial1/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, FastEthemet0/0
D. 208.149.23.64[110/3] via 190.172.23.10, 00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10, 00:00:16, Serial1/0
Answer: A
Explanation:
Router_E learns two subnets subnets 208.149.23.64 and 208.149.23.96 via Router_A
through FastEthernet interface. The interface cost is calculated with the formula 108 /
Bandwidth. For FastEthernet it is 108 / 100 Mbps = 108 / 100,000,000 = 1. Therefore the
cost is 12 (learned from Router_A) + 1 = 13 for both subnets ->
The cost through T1 link is much higher than through T3 link (T1 cost = 108 / 1.544 Mbps =
64; T3 cost = 108 / 45 Mbps = 2) so surely OSPF will choose the path through T3 link ->
Router_E will choose the path from Router_A through FastEthernet0/0, not Serial1/0.
In fact, we can quickly eliminate answers B, C and D because they contain at least one
subnet learned from Serial1/0 -> they are surely incorrect.
Q12. - (Topic 7)
Which feature allows a device to use a switch port that is configured for half-duplex to access the network?
A. CSMA/CD
B. IGMP
C. port security
D. split horizon
Answer: A
Explanation:
Ethernet began as a local area network technology that provided a half-duplex shared channel for stations connected to coaxial cable segments linked with signal repeaters. In this appendix, we take a detailed look at the half-duplex shared-channel mode of operation, and at the CSMA/CD mechanism that makes it work. In the original half-duplex mode, the CSMA/CD protocol allows a set of stations to compete for access to a shared Ethernet channel in a fair and equitable manner. The protocol’s rules determine the behavior of Ethernet stations, including when they are allowed to transmit a frame onto a shared Ethernet channel, and what to do when a collision occurs. Today, virtually all devices are connected to Ethernet switch ports over full-duplex media, such as twisted-pair cables. On this type of connection, assuming that both devices can support the full-duplex mode of operation and that Auto-Negotiation (AN) is enabled, the AN protocol will automatically select the highest-performance mode of operation supported by the devices at each end of the link. That will result in full-duplex mode for the vast majority of Ethernet connections with modern interfaces that support full duplex and AN.
Q13. - (Topic 1)
Refer to the exhibit.
The exhibit is showing the topology and the MAC address table. Host A sends a data frame to host D. What will the switch do when it receives the frame from host A?
A. The switch will add the source address and port to the MAC address table and forward the frame to host D.
B. The switch will discard the frame and send an error message back to host A.
C. The switch will flood the frame out of all ports except for port Fa0/3.
D. The switch will add the destination address of the frame to the MAC address table and forward the frame to host D.
Answer: A
Explanation:
When switch receives the data frame from the host not having the MAC address already on the MAC table, it will add the MAC address to source port on MAC address table and sends the data frame.
Q14. - (Topic 5)
Refer to the exhibit.
The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent?
A. The network is likely to be congested, with the result that packets are being intermittently dropped.
B. The branch router had to resolve the application server MAC address.
C. There is a short delay while NAT translates the server IP address.
D. A routing table lookup delayed forwarding on the first two ping packets.
E. The branch router LAN interface should be upgraded to FastEthernet.
Answer: B
Explanation:
Initially the MAC address had to be resolved, but once it is resolved and is in the ARP table of the router, pings go through immediately.
Q15. - (Topic 3)
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Answer: C,D
Explanation:
Multiple OSPF processes can be configured on a router using multiple process ID’s.
The valid process ID’s are shown below: Edge-B(config)#router ospf <1-65535> Process ID
Up to the immediate present 100-105 exam guide:
Q16. - (Topic 3)
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 8
C. 16
D. unlimited
Answer: B
Explanation:
Maximum-paths (OSPF)
To control the maximum number of parallel routes that Open Shortest Path First (OSPF)
can support, use the maximum-paths command.
Syntax Description
maximum
Maximum number of parallel routes that OSPF can install in a routing table. The range is from 1 to 16 routes.
Command Default
8 paths
Q17. - (Topic 7)
Which function enables an administrator to route multiple VLANs on a router?
A. IEEE 802 1X
B. HSRP
C. port channel
D. router on a stick
Answer: D
Q18. - (Topic 3)
How many bits are contained in each field of an IPv6 address?
A. 24
B. 4
C. 8
D. 16
Answer: D
Explanation:
One of the key advantages IPv6 brings is the exponentially larger address space. The
following will outline the basic address architecture of IPv6. 128-bit-long addresses Represented in hexadecimal format: Uses CIDR principles: prefix/prefix length x:x:x:x:x:x:x:x, where x is a 16-bit hex field The last 64 bits are used for the interface ID http://www.cisco.com/en/US/technologies/tk648/tk872/technologies_white_paper0900aecd 8026003d.pdf
Q19. - (Topic 5)
Which two of the following are true regarding the configuration of RouterA? (Choose two.)
A. At least 5 simultaneous remote connections are possible
B. Only telnet protocol connections to RouterA are supported C. Remote connections to RouterA using telnet will succeed
D. Console line connections will nevertime out due to inactivity
E. Since DHCP is not used on Fa0/1 there is not a need to use the NAT protocol
Answer: A,C
Q20. - (Topic 1)
Refer to the exhibit.
What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?
A. VLAN 1 on RT-A
B. IP routing on SW-A
C. default gateway on SW-A
D. crossover cable connecting SW-A and RT-A
Answer: C
Explanation:
In order for the switch to reach networks that are not local, such as networks attached to different interfaces of the router, it will need to set its default gateway to be the IP address of the attached router.