Foolproof ccent 100 105 tips

Act now and download your Cisco icnd1 100 105 pdf test today! Do not waste time for the worthless Cisco icnd 100 105 tutorials. Download Rebirth Cisco Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) exam with real questions and answers and begin to learn Cisco 100 105 exam with a classic professional.

Q1. - (Topic 7) 

By default, how many MAC addresses are permitted to be learned on a switch port with port security enabled? 

A. 8 

B. 2 

C. 1 

D. 0 

Answer: C 

Q2. - (Topic 5) 

Refer to the exhibit. 

A network administrator is troubleshooting a connectivity problem on the serial interfaces. The output from the show interfaces command on both routers shows that the serial interface is up, line protocol is down. Given the partial output for the show running-config in the exhibit, what is the most likely cause of this problem? 

A. The serial cable is bad. 

B. The MTU is incorrectly configured. 

C. The Layer 2 framing is misconfigured. 

D. The IP addresses are not in the same subnet. 

Answer: C 

Explanation: 

Here we see that Rtr3 is configured to use PPP encapsulation, but Rtr1 has not been configured for any kind of encapsulation. The default on Cisco router serial interfaces is HDLC, not PPP, so there is an encapsulation mismatch. 

Q3. - (Topic 1) 

Which two characteristics apply to Layer 2 switches? (Choose two.) 

A. Increases the number of collision domains 

B. Decreases the number of collision domains 

C. Implements VLAN 

D. Decreases the number of broadcast domains 

E. Uses the IP address to make decisions for forwarding data packets 

Answer: A,C 

Explanation: 

Layer 2 switches offer a number of benefits to hubs, such as the use of VLANs and each switch port is in its own separate collision domain, thus eliminating collisions on the segment. 

Q4. - (Topic 1) 

Refer to the exhibit. 

A network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation? 

A. a router with two Ethernet interfaces 

B. a switch with two Ethernet interfaces 

C. a router with one Ethernet and one serial interface 

D. a switch with one Ethernet and one serial interface 

E. a router with one Ethernet and one modem interface 

Answer: C 

Explanation: 

Only a router can terminate a leased line attachment access circuit, and only a router can connect two different IP networks. Here, we will need a router with two interfaces, one serial connection for the line attachment and one Ethernet interface to connect to the switch on the LAN. 

Q5. - (Topic 5) 

An administrator has connected devices to a switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. 

What must be done to accomplish this? 

A. Enable port security and use the keyword sticky. 

B. Set the switchport mode to trunk and save the running configuration. 

C. Use the switchport protected command to have the MAC addresses added to the configuration. 

D. Use the no switchport port-security command to allow MAC addresses to be added to the configuration. 

Answer: A 

Explanation: 

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide 

/port_sec.pdf 

One can configure MAC addresses to be sticky. These can be dynamically learned or manually configured, stored in the address table, and added to the running configuration. If these addresses are saved in the configuration file, the interface does not need to dynamically relearn them when the switch restarts, hence enabling security as desired. 

Q6. - (Topic 7) 

Which route source code represents the routing protocol with a default administrative distance of 90 in the routing table? 

A. S 

B. E 

C. D 

D. R 

E. O 

Answer: C 

Explanation: 

SStatic EEGP DEIGRP RRIP OOSPF 

Default Administrative distance of EIGRP protocol is 90 then answer is C 

Default Distance Value TableThis table lists the administrative distance default values of the protocols that Cisco supports: 

Route Source Default Distance Values 

Connected interface 0 Static route 1 Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5 External Border Gateway Protocol (BGP) 20 Internal EIGRP 90 IGRP 100 OSPF 110 Intermediate System-to-Intermediate System (IS-IS) 115 Routing Information Protocol (RIP) 120 Exterior Gateway Protocol (EGP) 140 On Demand Routing (ODR) 160 External EIGRP 170 Internal BGP 200 Unknown* 255 

Q7. - (Topic 7) 

On which type of device is every port in the same collision domain? 

A. a router B. a Layer 2 switch 

C. a hub 

Answer: C 

Explanation: Collision domainA collision domain is, as the name implies, a part of a network where packet collisions can occur. A collision occurs when two devices send a packet at the same time on the shared network segment. The packets collide and both devices must send the packets again, which reduces network efficiency. Collisions are often in a hub environment, because each port on a hub is in the same collision domain. By contrast, each port on a bridge, a switch or a router is in a separate collision domain. 

Q8. - (Topic 3) 

OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF? 

A. 2 

B. 3 

C. 4 

D. 5 

E. 6 

F. 7 

Answer: C 

Explanation: 

Although OSPF is configured using default classful addressing but OSPF is a link-state routing protocol so it will always send the subnet mask of each network in their advertised routes. Therefore R1 will learn the the complete subnets. Four networks list below will be in the routing table of R1:+ 172.16.2.64/30+ 172.16.2.228/30+ 172.16.2.232/30+ 172.16.3.0/24 Note: Other networks will be learned as “Directly connected” networks (marked with letter “C”) 

Q9. CORRECT TEXT - (Topic 6) 

There are three locations in a school district of a large city: ROUTER -M, ROUTER -W and ROUTER -U. The network connection between two of these locations has already functioned. Configure the ROUTER -M router IP addresses on the E0 and S0 interfaces so that the E0 receives the first usable subnet while the S0 receives the second usable subnet from the network 192.168.160.0/28. Both interfaces would receive the last available ip address on the proper subnet. 

NotE. The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process. 

Answer: ROUTER-M> enable PassworD. Cisco ROUTER-M# config t ROUTER-M(config)# interface e0 ROUTER-M(config-if)# ip address 192.168.160.14 255.255.255.240 

ROUTER-M(config-if)# no shutdown ROUTER -M(config-if)# exit ROUTER -M(config)# interface s0 ROUTER-M(config-if)# ip address 192.168.160.30 255.255.255.240 ROUTER-M(config-if)# no shutdown ROUTER-M(config-if)# end ROUTER-M# copy run start 

Q10. - (Topic 3) 

A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table? 

A. the OSPF route 

B. the EIGRP route 

C. the RIPv2 route 

D. all three routes 

E. the OSPF and RIPv2 routes 

Answer: B 

Explanation: 

When one route is advertised by more than one routing protocol, the router will choose to use the routing protocol which has lowest Administrative Distance. The Administrative Distances of popular routing protocols are listed below: