What Up to the immediate present 156-115.77 Is?

Cause all that matters here is passing the Check Point 156-115.77 exam. Cause all that you need is a high score of 156-115.77 Check Point Certified Security Master exam. The only one thing you need to do is downloading Pass4sure 156-115.77 exam study guides now. We will not let you down with our money-back guarantee.

Q81. - (Topic 5) 

According to this Rule Base, templates will be created until which rule? 

A. Rule 4 

B. Rule 2 

C. Rule 3 

D. Rule 5 

Answer:


Q82. - (Topic 9) 

Your Customer would like to enable IPS in his Corporate Cluster, but he is concerned about high CPU usage because if the IPS inspection. What feature would you configure to disable inspection if a high CPU usage develops? 

A. It is not possible. In this case no enable IPS 

B. Bypass Under Load. (In IPS Option on Gateway Properties) 

C. Bypass Inspection. (In IPS Option on Gateway Properties) 

D. Disable Inspection. (In IPS Option on Gateway Properties) 

Answer:


Q83. - (Topic 11) 

You are configuring VTIs in a clustered environment. On Peer A the VTI name is VT_Cluster_GWA and on Peer B the VTI name is VT_Cluster_GWB. You find that the route-based tunnel is not coming up. What could be the cause? 

A. The names for your peers have been reversed. 

B. You have not issued the command “vpn write config’ command. 

C. You have not licensed your gateways for VTIs. 

D. All VTIs going to the same remote peer must have the same name. 

Answer:


Q84. - (Topic 8) 

What command displays the Connections Table for a specified CoreXL firewall instance? 

A. fw tab –t connections –s 

B. fw -i.FW_INSTANCE_ID.tab -t connections [flags] C. fw tab –t connection | grep fw<FW_INSTANCE_ID> 

D. fw tab –t connections 

Answer:


Q85. - (Topic 5) 

While troubleshooting high CPU usage on cores 3 and 4 on a cluster, you notice the following output of fwaccel stats -s: 

What could be a possible cause of the high CPU usage? 

A. Connections are being partially accelerated by SecureXL, but too many packets are still being processed by the firewall kernel. 

B. The Secure Network Dispatcher (SND) is having to process too much inbound traffic from the NICs. 

C. Connections are not being accelerated by SecureXL, and all packets are being forwarded to firewall kernel instances for inspection. 

D. The Secure Network Dispatcher (SND) is working too hard to distribute the traffic to the acceleration layer. 

Answer:


Q86. - (Topic 6) 

What does the command fwaccel templates do? 

A. Starts firewall acceleration after fwaccel off was run or SecureXL was enabled by using the command cpconfig. 

B. That SecureXL has been enabled in the cpconfig command menu. 

C. Shows templates existing in the SecureXL device. This is so that an administrator can look for the template that matches the specific traffic. 

D. The Rule Base mapping between actual rules and the template built up in Layer 2. 

Answer:


Q87. - (Topic 5) 

What command should a firewall administrator use to begin debugging SecureXL? 

A. fwaccel dbg api + verbose add 

B. fwaccel debug –m <module name> <flag> 

C. fwaccel dbg -m <module name> <flag> 

D. SecureXL cannot be dubugged and the kernel debug will give enough output to help the firewall administrator to understand the firewalls behaviour. The right command to use is fw ctl debug –m fw. 

Answer:


Q88. - (Topic 9) 

In IPS what does a high confidence rating mean? 

A. This is a rating for how confident Check Point is with catching this attack 

B. This is a rating for how likely this attack is to penetrate most systems 

C. There is a high likelihood of false positives 

D. There is a low likelihood of false positives 

Answer:


Q89. - (Topic 7) 

What is one way to check cluster status on two gateways running in HA mode? 

A. show cluster 

B. cphaprob stat 

C. cp ha prob stat 

D. show cluster ha status 

Answer:


Q90. - (Topic 8) 

A Security Administrator wants to increase the amount of processing cores on a Check Point Security Gateway. He starts by increasing the number of cores, however the number of kernel instances remain the same way. What is the correct process to increase the number of kernel instances? 

A. Cpconfig- Enable Check Point CoreXL- Change the number of firewall instances-define how many firewall instances to enable-cprestart 

B. Cpconfig- Check Point CoreXL- Change the number of firewall instances-define how many firewall instances to enable-reboot 

C. Cpconfig- Enable Check Point ClusterXL- Change the number of firewall instances-define how many firewall instances to enable-reboot 

D. Cpconfig- Check Point CoreXL- Change the number of firewall instances-define how many firewall instances to enable-cpstop,cpstart 

Answer: