15 tips on vce 200-101

Best Quality of 200-101 real exam materials and study guides for Cisco certification for IT specialist, Real Success Guaranteed with Updated 200-101 pdf dumps vce Materials. 100% PASS Interconnecting Cisco Networking Devices Part 2 (ICND2) exam Today!

2016 Apr 200-101 Study Guide Questions:

Q1. Refer to the exhibit. 


A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. Based on the output from the show vlan brief command issued on Sw12, what will be the result of making this change on Sw11? 

A. Only the hosts in VLAN 1 on the two switches will be able to communicate with each other. 

B. The hosts in all VLANs on the two switches will be able to communicate with each other. 

C. Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other. 

D. Hosts will not be able to communicate between the two switches. 

Answer: D 


Q2. Refer to the exhibit. 


Which WAN protocol is being used? 

A. ATM 

B. HDLC 

C. Frame Relay 

D. PPP 

Answer: C 


Q3. What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.) 

A. reduced cost 

B. better throughput 

C. broadband incompatibility 

D. increased security 

E. scalability 

F. reduced latency 

Answer: ADE 


Q4. Refer to the exhibit. 


Which of these correctly describes the results of port security violation of an unknown packet? 

A. port enabled; unknown packets dropped; no SNMP or syslog messages 

B. port enabled; unknown packets dropped; SNMP or syslog messages 

C. port disabled; no SNMP or syslog messages 

D. port disabled; SNMP or syslog messages 

Answer: D 


Q5. What is the purpose of Inverse ARP? 

A. to map a known IP address to a MAC address 

B. to map a known DLCI to a MAC address 

C. to map a known MAC address to an IP address 

D. to map a known DLCI to an IP address 

E. to map a known IP address to a SPID 

F. to map a known SPID to a MAC address 

Answer: D 


200-101 testing engine

Most recent 200-101 pdf dump:

Q6. What command is used to verify the DLCI destination address in a Frame Relay static configuration? 

A. show frame-relay pvc 

B. show frame-relay lmi 

C. show frame-relay map 

D. show frame relay end-to-end 

Answer: C 


Q7. What are three characteristics of the OSPF routing protocol? (Choose three.) 

A. It converges quickly. 

B. OSPF is a classful routing protocol. 

C. It uses cost to determine the best route. 

D. It uses the DUAL algorithm to determine the best route. 

E. OSPF routers send the complete routing table to all directly attached routers. 

F. OSPF routers discover neighbors before exchanging routing information. 

Answer: ACF 


Q8. Refer to the exhibit. 


When running EIGRP, what is required for RouterA to exchange routing updates with RouterC? 

A. AS numbers must be changed to match on all the routers 

B. Loopback interfaces must be configured so a DR is elected 

C. The no auto-summary command is needed on Router A and Router C 

D. Router B needs to have two network statements, one for each connected network 

Answer: A 


Q9. Refer to the exhibit. 


Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2? 

A. Any packet destined for a network that is not directly connected to router R1 will be dropped. 

B. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately. 

C. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1. 

D. The networks directly connected to router R2 will not be able to communicate with the 172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks. 

E. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur. 

Answer: E 


Q10. Refer to the exhibit. 


What information about the interfaces on the Main_Campus router is true? 

A. The LAN interfaces are configured on different subnets. 

B. Interface FastEthernet 0/0 is configured as a trunk. 

C. The Layer 2 protocol of interface Serial 0/1 is NOT operational. 

D. The router is a modular router with five FastEthernet interfaces. 

E. Interface FastEthernet 0/0 is administratively deactivated. 

Answer: B 


200-101 exam price

Verified actual test 200-101:

Q11. DRAG DROP 


Answer: 



Q12. Which statements are true about EIGRP successor routes? (Choose two.) 

A. A successor route is used by EIGRP to forward traffic to a destination. 

B. Successor routes are saved in the topology table to be used if the primary route fails. 

C. Successor routes are flagged as 'active' in the routing table. 

D. A successor route may be backed up by a feasible successor route. 

E. Successor routes are stored in the neighbor table following the discovery process. 

Answer: AD 


Q13. Which three statements about RSTP are true? (Choose three.) 

A. RSTP significantly reduces topology reconverging time after a link failure. 

B. RSTP expands the STP port roles by adding the alternate and backup roles. 

C. RSTP port states are blocking, discarding, learning, or forwarding. 

D. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does. 

E. RSTP also uses the STP proposal-agreement sequence. 

F. RSTP uses the same timer-based process as STP on point-to-point links. 

Answer: ABD 


Q14. OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF? 



A. 2 

B. 3 

C. 4 

D. 5 

E. 6 

F. 7 

Answer: C 


Q15. What can be done to Frame Relay to resolve split-horizon issues?(Choose two.) 

A. Disable Inverse ARP. 

B. Create a full-mesh topology. 

C. Develop multipoint subinterfaces. 

D. Configure point-to-point subinterfaces. 

E. Remove the broadcast keyword from the frame-relay map command. 

Answer: BD 



see more http://www.2passeasy.com/exam/200-101/