Get Smart with cisco ccna 200 125

Cause all that matters here is passing the Cisco ccna 200 125 exam. Cause all that you need is a high score of 200 125 ccna CCNA Cisco Certified Network Associate CCNA (v3.0) exam. The only one thing you need to do is downloading Actualtests ccna 200 125 exam study guides now. We will not let you down with our money-back guarantee.


The article at Testaimer.com going over http://www.testaimer.com/200-125-test is very comprehensive.

Q111.  - (Topic 8)

Which IPv6 header field is equivalent to the TTL?

A. Hop Limit

B. Flow Label

C. TTD

D. Hop Count

E. Scan Timer

Answer: A


Q112.  - (Topic 8)

Refer to the exhibit.

While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?

A. the percentage of use of the link

B. the preference of the link

C. the session count of the link

D. the number source-destination pairs on the link

Answer: D


Q113.  - (Topic 8)

A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?

A. the EIGRP route

B. the OSPF route

C. the RIPv2 route

D. all three routes

E. the OSPF and RIPv2 routes

Answer: A


Q114.  - (Topic 8)

Which action can change the order of entries in a named access list?

A. opening the access list in Notepad.

B. resequercing

C. removing an entry

D. adding an entry

Answer: B


Q115.  - (Topic 8)

Which Cisco platform can verify ACLs?

A. Cisco Prime Infrastructure

B. Cisco Wireless LAN Controller

C. Cisco APIC-EM

D. Cisco IOS-XE

Answer: B


Q116.  - (Topic 7)

Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)

A. ping

B. tracert

C. ipconfig

D. show ip route

E. winipcfg

F. show interfaces

Answer: A,D,F

Explanation:

Ping, show ip route, and show interfaces are all valid troubleshooting IOS commands. Tracert, ipconfig, and winipcfg are PC commands, not IOS.


Q117.  - (Topic 8)

Which option is the default switch port port-security violation mode?

A. shutdown

B. protect

C. shutdown vlan

D. restrict

Answer: A

Explanation:

Shutdown—This mode is the default violation mode; when in this mode, the switch will automatically force the switchport into an error disabled (err-disable) state when a violation occurs. While in this state, the switchport forwards no traffic. The switchport can be brought out of this error disabled state by issuing the errdisable recovery cause CLI command or by disabling and reenabling the switchport.

Shutdown VLAN—This mode mimics the behavior of the shutdown mode but limits the error disabled state the specific violating VLAN.


Q118.  - (Topic 8)

Which two statements about unique local IPv6 addresses are true?

A. They are identical to IPv4 private addresses.

B. They are defined by RFC 1884.

C. They use the prefix FEC0::/10

D. They use the prefix FC00::/7

E. They can be routed on the IPv6 global internet.

Answer: A,D


Q119.  - (Topic 8)

Which condition does the err-disabled status indicate on an Ethernet interface?

A. There is a duplex mismatch.

B. The device at the other end of the connection is powered off.

C. The serial interface is disabled.

D. The interface is configured with the shutdown command.

E. Port security has disabled the interface.

F. The interface is fully functioning.

Answer: E


Q120.  - (Topic 6)

Refer to the exhibit.

A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands.

Which two of these changes are necessary for SwitchA to meet the requirements? (Choose two.)

A. Port security needs to be globally enabled.

B. Port security needs to be enabled on the interface.

C. Port security needs to be configured to shut down the interface in the event of a violation.

D. Port security needs to be configured to allow only one learned MAC address.

E. Port security interface counters need to be cleared before using the show command.

F. The port security configuration needs to be saved to NVRAM before it can become active.

Answer: B,D

Explanation:

From the output we can see that port security is disabled so this needs to be enabled. Also, the maximum number of devices is set to 2 so this needs to be just one if we want the single host to have access and nothing else.