All About 210-065 exam engine Jun 2021

Precise of 210-065 practice test materials and free samples for Cisco certification for IT learners, Real Success Guaranteed with Updated 210-065 pdf dumps vce Materials. 100% PASS Implementing Cisco Video Network Devices v1.0 exam Today!

The article at going over is very comprehensive.

Q11. How does a Cisco TCS process incoming video calls? 

A. Recording Alias > Template > Media Server Configuration 

B. Recording Alias > Media Server Configuration > Template 

C. Recording Alias > Media Server Configuration > H.323 > Template 

D. Recording Alias > Workflow > Template > Media Server Configuration 


Q12. Refer to the exhibit. 

A call with a destination alias of 15551001234 reaches a Cisco TelePresence VCS. Which transform will the destination alias match? 

A. Transform 1 

B. Transform 2 

C. Transform 3 

D. Transform 4 


Q13. A Cisco TelePresence VCS displays this alarm: "Root password is set to default." How can this security warning be addressed? 

A. Use the Cisco TelePresence VCS web user interface, choose Administration > User Settings, and change the root password. 

B. Use SSH to log in to the Cisco TelePresence VCS as Administrator and issue the command xconfig root set passwd. 

C. Use SSH to log in to the Cisco TelePresence VCS as Root, issue the command set password, and enter the new password when prompted. 

D. Use SSH to log in to the Cisco TelePresence VCS as Root, issue the command passwd, and enter the new password when prompted. 

E. Use the Cisco TelePresence VCS web user interface, choose Administration > System Settings, and change the root password. 


Q14. Refer to the exhibit. 

You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system? 

A. The Cisco TelePresence profile systems do not support dual display. 

B. The display is not powered on. 

C. The dual display option key has not been input into the codec. 

D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display. 


Q15. Which function does a Cisco TCS recording alias perform? 

A. It links recorded media to a specified output location. 

B. It provides a dialable alias that will trigger a TCS recording workflow. 

C. It sends media to Cisco Medianet. 

D. It provides an alias for the recorded filename. 


Q16. A user is currently on a Cisco TelePresence call using a Touch 8 device and would like to change the local screen layout so that the active speaker is in full screen and the other participants are smaller within the picture. Which layout option should the user choose? 

A. Prominent 

B. Overlay 

C. PiP 

D. FullScreen 


Q17. In this item, you will need to use all information presented to you to successfully answer the question. 

The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue? 

A. The subnet mask on the codec is incorrect. 

B. The ip address of the codec is incorrect. 

C. The interface that the codec is in is in the wrong VLAN. 

D. The codec did not receive a DHCP address from the DHCP server. 



The subnet mask configured on the codec is, when it should be 

Q18. Refer to the exhibit. 

A technician is reviewing the search history details on a Cisco TelePresence VCS for a recent call that failed. What was the cause for the call setup failure? 

A. A local call policy rule denied the call. 

B. The source alias matched an entry in the registration deny list. 

C. The originating caller was not authenticated. 

D. The source alias origin is unknown. 

Answer: A

Q19. Which four features are supported by Cisco TelePresence Server for all hardware models in remotely managed mode? (Choose four.) 

A. auto-attendant 

B. ClearPath 

C. Cluster sizes of more than 5 servers 

D. Cascading 

E. Active presence for all devices 

F. Support for Conductor 

G. Native scheduling capabilities 

Answer: B,D,E,F 

Q20. Refer to the exhibit. 

Which system tab can be used to add video infrastructure devices and endpoints? 

A. Navigator 

B. System Overview 

C. Configuration Templates 

D. Provisioning 

E. Administrative Tools