Where to find cisco 300 075
we provide Virtual Cisco 300 075 dump braindumps which are the best for clearing 300 075 ciptv2 test, and to get certified by Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2). The 300 075 dump Questions & Answers covers all the knowledge points of the real 300 075 pdf exam. Crack your Cisco 300 075 vce Exam with latest dumps, guaranteed!
The article at Testaimer.com going over http://www.testaimer.com/300-075-test is very comprehensive.
Q1. Which two options are requirements for deploying an H.323 gateway with Cisco Unified Communications Manager? (Choose two.)
A. Cisco Unified Communications Manager and the H.323 gateway must be configured use the same TCP port for H.323 calls.
B. The H.245TCSTimeout timer must be set to at least 25.
C. Cisco voicemail ports must be active.
D. The Media Exchange Interface Capability Timer must be set to less than 20.
E. The Media Exchange Timer must be set to less than 20.
Answer: A,B
Q2. Which two features require or may require configuring a SIP trunk? (Choose two.)
A. SIP gateway
B. Call Control Discovery between a Cisco Unified Communications Manager and Cisco Unified Communications Manager Express
C. Cisco Device Mobility
D. Cisco Unified Mobility
E. registering a SIP phone
Answer: A,B
Explanation:
Incorrect Answer: C, D, E All protocols require that either a signaling interface (trunk) or a gateway be created to accept and originate calls. Device mobility allows Cisco Unified Communications Manager to determine whether the phone is at its home location or at a roaming location. Cisco Unified Mobility gives users the ability to redirect incoming IP calls from Cisco Unified Communications Manager to different designated phones, such as cellular phones. Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmsys/a08sip.html# wpxref77849
Q3. Refer to the exhibit.
Assuming the regions configuration to BR only permits G.729 codec, how many calls are allowed for the BR location?
A. Total of four calls; two incoming and two outgoing.
B. Total of two calls in either direction.
C. Total of four calls to the BR location. Outgoing calls are not impacted by the location configuration.
D. Total of four calls in either direction.
E. Two outgoing calls. Incoming calls are unlimited.
Answer: D
Explanation:
Incorrect Answer: A, B, C, E In performing location bandwidth calculations for purposes of call admission control, Cisco Unified Communications Manager assumes that each G.729 call stream consumes 24 kb/s amount of bandwidth Link:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmsys/a02cac.html #wpxref28640
Q4. Assume that the Cisco IOS SAF Forwarder is configured correctly. Which minimum configurations on Cisco Unified Communications Manager are needed for the SAF registration to take place?
A. SAF Trunk, SAF Security Profile, SAF Forwarder, and CCD Advertising Service
B. SAF Trunk, SAF Security Profile, SAF Forwarder, and CCD Requesting Service
C. SAF Trunk, SAF Security Profile, SAF Forwarder, CCD Requesting Service, and CCD Advertising Service
D. SAF Trunk, SAF Security Profile, and SAF Forwarder
E. SAF Trunk, CCD Requesting Service, and CCD Advertising Service
Answer: B
Q5. Refer to the exhibit.
All HQ phones are configured to use HQ_MRGL and all BR phones are configured to use BR_MRGL. For the HQ phones always to use the hardware conference bridge as a first choice, which configuration should be implemented?
A. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. Ensure that the instance ID for the hardware conference bridge is 0.
B. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. The hardware conference bridge must be configured first.
C. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Add both the HQ_MRG and HQ_MRG_2 to the HQ_MRGL and list the HQ_MRG first.
D. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Configure an additional HQ_MRGL_2. Add the HQ_MRG to HQ_MRGL. Add HQ_MRG_2 to HQ_MRGL_2. The HQ_MRGL should be assigned to the HQ phones. The HQ_MRGL_2 should be assigned to the HQ device pool.
Answer: C
Q6. Refer to the exhibit.
The HQ site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number.
Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit.
Which partition should be configured in the AAR CSS applied at the phones?
A. PSTN partition
B. LD partition
C. The HQ AAR CSS must include a partition assigned to route pattern 91408XXXXXXX. The BR1 AAR CSS must include a partition assigned to route pattern 91650XXXXXXX.
D. AAR CSS must contain translation pattern 9.1[2-9]XX[2-9]XXXXXX for each site that must be globalized. Otherwise the called numbers will not be localized at the egress gateway.
Answer: A
Q7. With Cisco Extension Mobility, when a user logs in to a phone type which has no user device profile, what will happen to the phone?
A. The phone takes on the default clusterwide device profile.
B. The phone creates a new device profile automatically.
C. The phone immediately logs the user off.
D. The phone crashes and reboots.
Answer: A
Q8. Which two options enable routers to provide basic call handling support for Cisco Unified IP Phones if they lose connection to all Cisco Unified Communications Manager systems?
(Choose two.)
A. SCCP fallback
B. Cisco Unified Survivable Remote Site Telephony
C. Cisco Unified Communications Manager Express
D. MGCP fallback
E. Cisco Unified Communications Manager Express in SRST mode
Answer: B,E
Q9. How is a SIP trunk in Cisco Unified Communications Manager configured for SIP precondition?
A. The configuration is done by selecting a SIP precondition trunk for trunk type.
B. The configuration is automatically selected when RSVP is enabled for the location assigned to the trunk.
C. SIP precondition is configured by selecting E2E for RSVP over SIP on the default SIP profile assigned to the SIP trunk.
D. SIP precondition is configured by configuring a new SIP profile and selecting E2E for RSVP over SIP. The new SIP profile must then be assigned to the SIP trunk.
Answer: D
Q10. Which task must you perform before deleting a transcoder?
A. Delete the dependency records.
B. Unassign it from a media resource group.
C. Use the Reset option.
D. Remove the device pool.
E. Remove the subunit.
F. Delete the common device configuration.
Answer: B