A Complete Guide to 300 075 dump
Actualtests offers free demo for 300 075 pdf exam. "Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2)", also known as 300 075 pdf exam, is a Cisco Certification. This set of posts, Passing the Cisco cisco 300 075 exam, will help you answer those questions. The 300 075 vce Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco 300 075 ciptv2 exams and revised by experts!
Q21. Which action configures PSTN backup for calls that are rejected by the gatekeeper CAC?
A. Configure AAR in Cisco Unified Communications Manager.
B. Configure CFUR in Cisco Unified Communications Manager.
C. Configure a route pattern, a route list, and route groups to a trunk and a gateway in Cisco Unified Communications Manager.
D. Configure a route pattern to a gateway in Cisco Unified Communications Manager.
Q22. Which solution is needed to enable presence and extension mobility to branch office phones during a WAN failure?
A. SRST with MGCP fallback
B. SRST without MGCP fallback
C. Cisco Unified Communications Manager Express in SRST mode
D. SRST with VoIP dial peers to Cisco Unified Communications Manager Express
Q23. How is a SIP trunk in Cisco Unified Communications Manager configured for SIP precondition?
A. The configuration is done by selecting a SIP precondition trunk for trunk type.
B. The configuration is automatically selected when RSVP is enabled for the location assigned to the trunk.
C. SIP precondition is configured by selecting E2E for RSVP over SIP on the default SIP profile assigned to the SIP trunk.
D. SIP precondition is configured by configuring a new SIP profile and selecting E2E for RSVP over SIP. The new SIP profile must then be assigned to the SIP trunk.
Q24. On which Cisco Unified Communications Manager configuration parameter does the CODEC that a Cisco IP Phone uses for a call depend?
A. enterprise parameters
B. media resources
C. physical location
Q25. Enabling authentication and encryption for CTI, JTAPI, and TAPI applications requires which two tasks? (Choose two.)
A. Enter the encryption key into the application.
B. Set up an IPsec association between the application and Cisco Unified CallManager.
C. Configure related security parameters in the CTI, JTAPI, and TAPI application.
D. Add the application user or end users to the Standard CTI Secure Connection user group, Standard CTI Allow Reception of SRTP Key Material user group, and Standard CTI Enabled user group.
Incorrect Answer: A, B You must also add the application users or the end users to the Standard CTI Secure Connection user group in Cisco Unified Communications Manager Administration to enable TLS for the application. After you add the user to this group and install the certificate, the application ensures that the user connects via the TLS port. Link:
Q26. Which system configuration is used to set a restriction on audio bandwidth?
C. physical location
Q27. Refer to the exhibit.
Which option describes the effect of this configuration?
A. It implements Cisco United CME redundancy.
B. It creates dial peers.
C. It configures failover.
D. It configures a standby Cisco United CME.
E. It implements HSRP.
F. It implements Cisco IOS redundancy.
Q28. Which device is used to connect to the H.323 gatekeeper?
A. H.323 gateway
B. SIP trunk
C. H.323 trunk
D. MGCP gateway
Q29. Refer to the exhibit.
Which trunks would be most suitable for Connection Y?
A. an H.225 trunk (gatekeeper-controlled)
B. intercluster trunk (gatekeeper-controlled)
C. a SIP trunk on the U.S. cluster and an intercluster trunk on the remote cluster
D. intercluster trunk (nongatekeeper-controlled)
E. No extra connections are required. As long as IP connectivity exists, you need only configure a route pattern for each site. The Cisco Unified Communications Manager will automatically forward the calls over the WAN if the destination directory number is not registered locally.
Q30. Where do you specify the device mobility group and physical location after they have been configured?
C. device mobility CSS
D. device pool
Incorrect Answer: A, B, C, E Before you configure a device pool, you must configure the following items if you want to choose them for the device pool, Cisco Unified Communications Manager group (required), Date/time group (required). Region (required) , SRST reference (optional). Media resource group list (optional), Calling search space for auto-registration (optional). Reverted call focus priority (optional), Device mobility group (optional), Device mobility calling search space, Physical location (optional). Location, AAR group. AAR calling search space. Link: