The Only Tip You Need: ccnp switch 300 115 labs
The article at Testaimer.com going over http://www.testaimer.com/300-115-test is very comprehensive.
Q41. What does the command vlan dot1q tag native accomplish when configured under global
configuration?
A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.
B. It allows control traffic to pass using the non-default VLAN.
C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).
D. Control traffic is tagged.
Answer: D
Q42. Which statement about Cisco Discovery Protocol configuration on a Cisco switch is true?
A. CDP is enabled by default and can be disabled globally with the command no cdp run.
B. CDP is disabled by default and can be enabled globally with the command cdp enable.
C. CDP is enabled by default and can be disabled globally with the command no cdp enable.
D. CDP is disabled by default and can be enabled globally with the command cdp run.
Answer: A
Q43. Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRP to provide a high availability solution.
• DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105
• DSW2 - primary device for VLAN 103 and VLAN 104
• A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1 and DSW2. All other interfaces were up. During this time, DSW1 became the active router for the VLAN 104HSRP group. As related to the VLAN 104HSRP group, what can to be done to make the group function properly?
A. On DSW1, disable preempt.
B. On DSW2 decrease the priority value to a value less than 150.
C. On DSW1, increase the decrement value in the track command to a value greater than 6.
D. On DSW1, decrease the decrement value in the track command to a value less than 1.
Answer: C
Q44. Refer to the exhibit.
The users in an engineering department that connect to the same access switch cannot access the network. The network engineer found that the engineering VLAN is missing from the database. Which action resolves this problem?
A. Disable VTP pruning and disable 802.1q.
B. Update the VTP revision number.
C. Change VTP mode to server and enable 802.1q.
D. Enable VTP pruning and disable 802.1q.
Answer: C
Q45. A Cisco Catalyst switch that is prone to reboots continues to rebuild the DHCP snooping database. What is the solution to avoid the snooping database from being rebuilt after every device reboot?
A. A DHCP snooping database agent should be configured.
B. Enable DHCP snooping for all VLANs that are associated with the switch.
C. Disable Option 82 for DHCP data insertion.
D. Use IP Source Guard to protect the DHCP binding table entries from being lost upon rebooting.
E. Apply ip dhcp snooping trust on all interfaces with dynamic addresses.
Answer: A
Q46. A network engineer notices inconsistent Cisco Discovery Protocol neighbors according to the diagram that is provided. The engineer notices only a single neighbor that uses Cisco Discovery Protocol, but it has several routing neighbor relationships. What would cause the output to show only the single neighbor?
A. The routers are connected via a Layer 2 switch.
B. IP routing is disabled on neighboring devices.
C. Cisco Express Forwarding is enabled locally.
D. Cisco Discovery Protocol advertisements are inconsistent between the local and remote devices.
Answer: A
Q47. Which option is a benefit of using VSS?
A. reduces cost
B. simplifies configuration
C. provides two independent supervisors with two different control planes
D. removes the need for a First Hop Redundancy Protocol
Answer: D
Q48. Which two protocols can be automatically negotiated between switches for trunking? (Choose two.)
A. PPP
B. DTP
C. ISL
D. HDLC
E. DLCI
F. DOT1Q
Answer: C,F
Q49. A network engineer must adjust the STP interface attributes to influence root port selection. Which two elements are used to accomplish this? (Choose two.)
A. port-priority
B. cost
C. forward-timers
D. link type
E. root guard
Answer: A,B
Q50. Which VTP mode is needed to configure an extended VLAN, when a switch is configured to use VTP versions 1 or 2?
A. transparent
B. client
C. server
D. Extended VLANs are only supported in version 3 and not in versions 1 or 2.
Answer: D