Tips for ccnp switch 300 115 dumps
Want to know Exambible certprepare 300 115 Exam practice test features? Want to lear more about Cisco Implementing Cisco IP Switched Networks certification experience? Study Pinpoint Cisco 300 115 pdf answers to Latest 9tut ccnp switch 300 115 questions at Exambible. Gat a success with an absolute guarantee to pass Cisco 300 115 pdf (Implementing Cisco IP Switched Networks) test on your first attempt.
Q1. Refer to the exhibit.
Which login credentials are required when connecting to the console port in this output?
A. none required
B. username cisco with password cisco
C. no username with password linepass
D. login authentication default
Answer: A
Q2. Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Answer: C
Q3. After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol
Answer: B
Q4. after UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.
Answer: B
Q5. Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?
A. sticky
B. dynamic
C. static
D. secure
Answer: A
Q6. refer to the exhibit.
f1/0 and f1/1 have the same end-to-end path cost to the designated bridge. Which action is needed to modify the Layer 2 spanning-tree network so that traffic for PC1 VLAN from switch SW3 uses switchport f1/1 as a primary port?
A. Modify the spanning-tree port-priority on SW1 f1/1 to 0 and f1/0 to 16.
B. Modify the spanning-tree port-priority on SW1 f1/1 to 16 and f1/0 to 0.
C. Modify the spanning-tree port-priority on SW2 f1/1 to 0 and f1/0 to 16.
D. Modify the spanning-tree port-priority on SW2 f1/1 to 16 and f1/0 to 0.
Answer: C
Q7. When you design a switched network using VTPv2, how many VLANs can be used to carry user traffic?
A. 1000
B. 1001
C. 1024
D. 2048
E. 4095
F. 4096
Answer: B
Q8. What is the maximum number of VLANs that can be assigned to an access switchport without a voice VLAN?
A. 0
B. 1
C. 2
D. 1024
Answer: B
Q9. After reviewing UDLD status on switch ports, an engineer notices that the." Which statement describes what this indicates about the status of the port?
A. The port is fully operational and no known issues are detected.
B. The bidirectional status of "unknown" indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.
C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.
D. The UDLD port is placed in the "unknown" state for 5 seconds until the next UDLD packet is received on the interface.
Answer: A
Q10. Which private VLAN access port belongs to the primary VLAN and can communicate with all interfaces, including the community and isolated host ports?
A. promiscuous port
B. isolated port
C. community port
D. trunk port
Answer: A