Secrets to examcollection 300 115

Exam Code: 300 115 switch (Practice Exam Latest Test Questions VCE PDF)
Exam Name: SWITCH Implementing Cisco IP Switched Networks
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass certprepare 300 115 Exam.

P.S. Accurate 300-115 vce are available on Google Drive, GET MORE: https://drive.google.com/open?id=1CfKI5pbjCPmPD71IOn4nWDyRdJ9zMspQ


New Cisco 300-115 Exam Dumps Collection (Question 15 - Question 24)

New Questions 15

Which two prerequisites for HSRP to become active on an interface are true? (Choose two.)

A. Cisco Express Forwarding must be disabled globally.

B. The VIP must be in the same subnet as the primary IP address.

C. A Virtual-MAC address must be configured on the interface.

D. An IP address must be configured on the interface.

E. PIM routing must be disabled on the interface.

Answer: B,D


New Questions 16

Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about the STP process for VLAN 200 are true? (Choose two.)

A. BPDUs will be sent out every two seconds.

B. The time spent in the listening state will be 30 seconds.

C. The time spent in the learning state will be 15 seconds.

D. The maximum length of time that the BPDU information will be saved is 30 seconds.

E. This switch is the root bridge for VLAN 200.

F. BPDUs will be sent out every 10 seconds.

Answer: B,F


New Questions 17

CORRECT TEXT

VTP Domain name : cisco VLAN Ids 20 31

IP Addresses 172.16.71.1/24 172.16.132.1/24

These are your specific tasks:

1. Configure the VTP information with the distribution layer switch as the VTP server

2. Configure the VTP information with the access layer switch as a VTP client

3. Configure VLANs on the distribution layer switch

4. Configure inter-VLAN routing on the distribution layer switch

5. Specific VLAN port assignments will be made as users are added to the access layer switches in the future.

6. All VLANs and VTP configurations are to completed in the global configuration To configure the switch click on the host icon that is connected to the switch be way of a serial console cable.

Answer:

Please refer to explanation below:

Explanation:

vtp server configuration:

switch#conf t

switch(config)#vtp mode server

switch(config)#vtp domain CISCO

switch(config)#vlan 20

switch(config)#vlan 31

switch(config)#int vlan 20

switch(if-config)#ip add 172.64.20.1 255.255.255.0

switch(if-config)#no shut

switch(if-config)#int vlan 31

switch(if-config)#ip add 192.162.31.1 255.255.255.0

switch(if-config)#no shut

switch(if-config)#exit switch#ip routing

switch#copy run start

vtp client configuration:

switch#conf t

switch(config)#vtp mode client

switch(config)#vtp domain CISCO

switch#copy run start

Alternative #1

VTP DomainDistribution VLAN Ids2031

IP Addresses172.16.16.1/24172.16.193.1/24

Alternative #12

VTP DomainDistribution

VLAN Ids3021

IP Addresses172.16.203.1/24172.16.93.1/24


New Questions 18

Refer to the exhibit.

Which two statements about SW1 are true? (Choose two)

A. Interface Gi5/1 is using a Cisco proprietary trunking protocol

B. On Interface Gi5/1, all untagged traffic is tagged with VLAN 113

C. The device is configured with the default MST region

D. Interface Gi5/1 is using an industry-standard trunking protocol

E. Interface Gi6/2 is the root port for VLAN 36

F. On interface Gi6/2, all untagged traffic is tagged with VLAN 600

Answer: D,F


New Questions 19

Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router? (Select the best answer.)

A. active

B. speak

C. learn

D. listen

E. init

F. standby

Answer: B


New Questions 20

Which two statements about static mac addresses are true ?

A. They are configured without an aging time

B. They have a default aging time of 300 seconds

C. They supersede dynamically learned mac address

D. They can be configured on multiple interfaces in the same vlan

E. They have a default aging time of 60 seconds.

Answer: B,D


New Questions 21

CORRECT TEXTThe headquarter office for a cement manufacturer is installing a temporary Catalyst 3550 in an IDF to connect 24 additional users.

To prevent network corruption, it is important to have the correct configuration prior to connecting to the

production network.

It will be necessary to ensure that the switch does not participate in VTP but forwards VTP advertisements that are received on trunk ports.

Because of errors that have been experienced on office computers, all non-trunking interfaces should transition immediately to the forwarding state of Spanning tree. Also configure the user ports (all FastEthernet ports) so that the ports are permanently non-trunking.

Requirement:

You will configure FastEthernet ports 0/12 through 0/24 for users who belong to VLAN 20. Also all VLAN and VTP configurations are to be completed in global configuration mode as VLAN database mode is being

deprecated by Cisco. You are required to accomplish the following tasks:

1. Ensure the switch does not participate in VTP but forwards VTP advertisements received on trunk ports.

2. Ensure all non-trunking interfaces (Fa0/1 to Fa0/24) transition immediately to the forwarding state of

Spanning-Tree.

3. Ensure all FastEthernet interfaces are in a permanent non-trunking mode.

4. Place FastEthernet interfaces 0/12 through 0/24 in VLAN 20.

Answer:

Please Refer to Explanation below for details:

Explanation/Reference:

Console into the Switch Switch>enable Switch#configure terminal

Switch(config)#interface range fa0/1 u2013 24

Switch(config-if-range)#switchport mode access <<Make all FastEthernet interfaces into access mode.

Switch(config-if-range)#spanning-tree portfast <<Enables the PortFast on interface. Next, we need to assign FastEthernet ports 0/12 through 0/24 to VLAN 20. By default, all ports on the switch

are in VLAN 1. To change the VLAN associated with a port, you need to go to each interface (or a range of

interfaces) and tell it which VLAN to be a part of. Switch(config-if-range)#interface range fa0/12 u2013 24

Switch(config-if-range)#switchport access vlan 20 <<Make these ports members of vlan 20 Switch(config-if-range)#exit

Next we need to make this switch in transparent mode. In this mode, switch doesnu2019t participate in the VTP

domain, but it still forwards VTP advertisements through any configured trunk links. Switch(config)#vtp mode transparent

Switch(config)#exit

Switch#copy running-config startup-config


New Questions 22

A network is considering implementing UDLD throughout the network. Which option must the network engineer consider?

A. UDLD work at Layer 1 of the OSI model.

B. UDLD aggressively disables the port after eight failed retries to connect to neighbor.

C. UDLD is already enabled by default on all ports on Cisco switches.

D. UDLD is an IEEE standard that can be configured on non-Cisco devices.

Answer: B


New Questions 23

Which two statements about VRRP advertisements are true? (Choose two)

A. They are sent every three seconds by default.

B. They include VRRP timer information.

C. They are sent from the master router and standby routers.

D. They are sent only from the master router.

E. They include priority information.

Answer: D,E

Explanation: VRRP AdvertisementsThe virtual router master sends VRRP advertisements to other VRRP routers in the same group. The advertisements communicate the priority and state of the virtual router master. The VRRP advertisements are encapsulated in IP

packets and sent to the IP Version 4 multicast address assigned to the VRRP group. The advertisements are sent every second by default; the interval is configurable.

Although the VRRP protocol as per RFC 3768 does not support millisecond timers, Cisco routers allow you to configure millisecond timers. You need to manually configure the millisecond timer values on both the primary and the backup routers. The master advertisement value displayed in the show vrrp command output on the backup routers is always 1 second because the packets on the backup routers do not accept millisecond values.

You must use millisecond timers where absolutely necessary and with careful consideration and testing. Millisecond values work only under favorable circumstances, and you must be aware that the use of the millisecond timer values restricts VRRP operation to Cisco devices only.


New Questions 24

Refer to the exhibit.

Which two statements about the network environment of the device that generated this output are true? (Choose two.)

A. The local device has a higher priority setting than the active router.

B. The virtual IP address of the HSRP group is 10.1.1.1

C. If a router with a higher IP address and same HSRP priority as the active router becomes available, that router becomes the new active router 5 seconds later.

D. if the local device fails to receive a hello from the active router for more than 5 seconds, it can become the active router.

E. The hello and hold timers are set to custom values.

Answer: B,C


100% Most recent Cisco 300-115 Questions & Answers shared by Certifytools, Get HERE: https://www.certifytools.com/300-115-exam.html (New 522 Q&As)