Improved 300-365 practice question Guide

It is more faster and easier to pass the Cisco 300-365 exam by using Vivid Cisco Deploying Cisco Wireless Enterprise Networks questuins and answers. Immediate access to the Renew 300-365 Exam and find the same core area 300-365 questions with professionally verified answers, then PASS your exam with a high score now.

2021 Mar 300-365 latest exam

Q21. VoWLAN implementation plans for a current mix of existing Cisco Unified Wireless IP Phones 7920G and 7921G to a final migration of Wireless IP Phones 7925G in a single WLAN. What would be the most appropriate WLC WLAN configuration to end with Wireless IP Phones 7925G? 

A. 7920 Client CAC = enabled only; Radio Policy = All; WMM = Disabled 

B. 7920 AP CAC = enabled only; Radio Policy = All; WMM = Allowed 

C. 7920 Client CAC = enabled only; Radio Policy = 802.11a only; WMM = Disabled 

D. 7920 AP CAC = enabled only; Radio Policy = 802.11a only; WMM = Allowed 

E. 7920 Client CAC = enabled only; Radio Policy = 802.11b/g only; WMM = Disabled 

F. 7920 AP CAC = enabled only; Radio Policy = 802.11b/g only; WMM = Allowed 


Q22. Controllers WLC_1 and WLC_2 are in the same mobility group. A wireless client that does not have the same VLAN interface roams from WLC_1 to WLC_2. What happens to the client roaming? 

A. The client context is deleted in controller WLC_1, and a new client context is created in WLC_2 to become the anchor controller 

B. The client context is moved from controller WLC_1 to controller WLC_2. The result is that the WLC_1 client context is deleted and WLC_2 becomes the anchor controller. 

C. The client context is copied from controller WLC_1 to controller WLC_2. The result is that WLC_1 becomes the foreign controller and WLC_2 becomes the anchor controller. 

D. The client context is copied from controller WLC_1 to controller WLC_2. The result is that WLC_1 becomes the anchor controller and WLC_2 becomes the foreign controller. 


Q23. A customer recently implemented WLC wireless multicast. Clients and connecting at the highest mandatory wireless rate of 24 Mbps and are receiving multicast traffic, but WLC cpu utilization and wired side network load has increased substantially. What three actions should the engineer take next to optimize the configuration? (Choose Three) 

A. verify that Global Multicast mode has been enabled 

B. verify that IGMP snooping is disabled on the wireless controller since the access points are handing IGMP messages from the clients. 

C. make sure the highest mandatory rate is set to 54 Mbps so that the multicast traffic has sufficient bandwidth 

D. verify Multicast Listener Discovery (MLD) v1 snooping has been enabled to keep track of and deliver IPv4 multicast flows 

E. change the wireless controller from Multicast-Unicastmodeto Multicast-Multicast mode and assign a multicast address in the 239.X.X.X/8 subnet 

F. verify that the L3 interfaces are configured for pirn sparse-dense-mode on the VLAN servicing the wireless access points as well as the wireless controller’s management VLAN 

Answer: A,B,E 

Q24. A customer has implemented several WLANs in an auditorium utilizing a newly dedicated WLC and is experiencing excessive channel utilization regardless of occupancy. Which action reduces channel utilization without removing SSIDs? 

A. Disable MCS data rates 0 through 11. 

B. Disable MCS data rates used by 40 MHz channels. 

C. Disable data rates that use CCK. 

D. Disable VHT data rates. 


Q25. A customer requires that an SSID is broadcasted to specific access points that use certain interfaces. Which feature can be used to achieve this goal? 

A. mobility groups 

B. flex-connect groups 

C. interface groups 

D. AP groups 


Up to the minute 300-365 exam answers:


Drag the QoS values from the left and drop them in the correct descending order of priority on the right. 


Q27. A network engineer is experiencing issues enabling LAG on the WLC. Which four characteristics should be validated to ensure LAG configuration? (Choose four.) 

A. All ports participate in the LAG by default when LAG is enabled on the controller, y 

B. Dynamic interfaces and management are moved to port 1 

C. Primary and secondary ports are needed for each interface. 

D. Multiple untagged interfaces to the same port are not allowed. 

E. EtherChannel must be configured for mode "on" on the switch. 

F. Only one functional physical port is needed to continue to pass traffic. 

G. Multiple LAGs are permitted on the controller. 

H. The WLC does not need to be rebooted to enable the LAG configuration. 

Answer: A,D,E,F 

Q28. A customer called into the support center with a problem ticket that involves wireless clients having to reauthenticate when they are walking around their office. After further investigation, it was discovered that the customer has two controllers in an N+1 deployment. Which action must the engineer take to troubleshoot the issue? 

A. Verify that the wireless controllers are in the same mobility group and that the access points are all on the primary controller. 

B. Under the SSID, make sure that 802.1 Iris configured and running for the clients. 

C. Make sure that the SSID has the authentication set to 802.1x with Cisco Centralized Key Management so the data clients can roam seamlessly. 

D. Verify the access points are spread out between the primary and secondary controller and that the controllers are in the same mobility group. 


Q29. An engineer wants to configure Call Admission Control and ensure that AC is based on the capacity of the AP and considering the possible impact of other APs in the area. Which two configuration options are required? (Choose two.) 

A. StaticCAC 

B. Admission Control 

C. Load-Based AC 

D. Add Traffic Stream 

E. Reserved Roaming Bandwidth 

F. Expedited Bandwidth 

Answer: B,C 

Q30. A customer requires that the remote site be able to utilize local servers when the AP is in WAN-down (standalone mode). Which AP mode must be configured on the wireless controller? 

A. SE-Connect 

B. Monitor 

C. Local 

D. FlexConnect 

E. Sniffer 

F. Rogue Detector