Avant-garde 352-001: Pass4sure real braindumps from 61 to 70

Cause all that matters here is passing the Cisco 352-001 exam. Cause all that you need is a high score of 352-001 CCDE Written Exam exam. The only one thing you need to do is downloading Pass4sure 352-001 exam study guides now. We will not let you down with our money-back guarantee.


The article at Testaimer.com going over http://www.testaimer.com/352-001-test is very comprehensive.

2021 Mar 352-001 exam prep

Q61. You are the lead network designer for an enterprise company called ABC, and you are leading design discussions regarding IPv6 implementation into their existing network. A question is raised regarding older Layer 2 switches that exist in the network, and if any changes are required to these Layer 2 switches for successful IPv6 implementation. Which two responses should you give? (Choose two.) 

A. IPv6 is transparent on Layer 2 switches, so there is no need to make any changes to the Layer 2 switches. 

B. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support ICMPv6 snooping at Layer 2 switches. 

C. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support DHCPv6 snooping at Layer 2 switches. 

D. If IPv6 multicast deployment is planned, then make sure that Layer 2 switches support MLD snooping at Layer 2 switches. 

E. If IPv6 anycast deployment is planned, then make sure that Layer 2 switches support ND snooping at Layer 2 switches. 

Answer: AD 


Q62. Which two design aspects should a metro service provider consider when planning to deploy REP for his backbone? (Choose two.) 

A. Two REP segments can be connected redundantly at two points, one connection will be blocked as per the STP defined in IEEE 802.1d. 

B. UDLD can be enabled on REP interfaces to detect unidirectional failures. 

C. The guaranteed convergence recovery time is less than 50 ms for the local segment. 

D. A REP segment is limited to a maximum of seven devices. 

E. VLAN load balancing for optimal bandwidth usage is supported in any REP segment. 

Answer: BE 


Q63. Which three techniques can be used to improve fault isolation in an enterprise network design? (Choose three.) 

A. aggregate routing information on an OSPF ABR 

B. fully meshed distribution layer 

C. Equal-Cost Multipath routing 

D. EIGRP query boundaries 

E. multiple IS-IS flooding domains 

F. tuned Spanning Tree Protocol timers 

Answer: ADE 


Q64. A network design includes a long signaling delay in notifying the Layer 3 control plane that an interface has failed. Which two of these actions would reduce that delay? (Choose two.) 

A. Enable lower data link layer recovery systems to have an opportunity to restore the interface. 

B. Increase the notification of interface flaps. 

C. Reduce the time for the network to reconverge. 

D. Increase network stability. 

Answer: AD 


Q65. Which design concern should be accounted for in all Layer 3 virtualization technologies? 

A. Layer 3 redundancy 

B. packet sizing 

C. application usage 

D. Layer 3 stability 

Answer:


Renewal 352-001 download:

Q66. You are creating a network design that will influence the traffic path across the MPLS core on a virtual private LAN. Which parameter is included in your design to manage the traffic? 

A. Deploy MPLS traffic engineering and modify the path using the preferred path. 

B. Deploy MPLS traffic engineering and modify the path using auto-route, static routing, or PBR. 

C. Create an MPLS traffic engineering tunnel and modify the path using a static route. 

D. Create an MPLS traffic engineering tunnel and modify the path using auto-route announce. 

Answer:


Q67. As part of a new network design, you are helping the Network Management Team to develop a proactive report to identify places in the network where problems may happen. The network management tool can poll the network devices only via SNMP GET operations. Which two threshold-crossing metrics should you include in this report? (Choose two.) 

A. packet loss 

B. CPU utilization 

C. heat dissipation 

D. IP reachability 

E. energy consumption 

F. link bandwidth utilization 

Answer: BF 


Q68. The network administrator of a branch office network has decided to deploy Unicast RPF at the access layer. He insists that the design must guarantee that all the packets arriving on the router interfaces are assigned to the same interface subnet. 

Which mode of Unicast RPF would you recommend as the lead network designer? 

A. uRPF strict mode 

B. uRPF loose mode 

C. uRPF VRF mode 

D. RPF feasible mode 

Answer:


Q69. Your design plan includes mutual redistribution of two OSPF networks at multiple locations, with connectivity to all locations in both networks. How is this accomplished without creating routing loops? 

A. Use route maps on the ASBRs to allow only internal routes to be redistributed. 

B. Use route maps on the ASBRs to allow internal and external routes to be redistributed. 

C. Use route maps on the ASBRs to set tags for redistributed routes. 

D. Use route maps on the ASBRs to filter routes with tags so they are not redistributed. 

Answer:


Q70. A green data center is being deployed and a design requirement is to be able to readily scale server virtualization. Which IETF standard technology can provide this requirement? 

A. Transparent Interconnection of Lots of Links 

B. fabric path 

C. data center bridging 

D. unified fabric 

Answer: