Top Renewal 400-101 braindumps Reviews!
Want to know Testking 400-101 Exam practice test features? Want to lear more about Cisco CCIE Routing and Switching (v5.0) certification experience? Study Certified Cisco 400-101 answers to Renovate 400-101 questions at Testking. Gat a success with an absolute guarantee to pass Cisco 400-101 (CCIE Routing and Switching (v5.0)) test on your first attempt.
The article at Testaimer.com going over http://www.testaimer.com/400-101-test is very comprehensive.
2021 Mar 400-101 exam fees
Q171. You are configuring a DHCPv6 client for a DHCPv6 server with the prefix delegation feature. Which option is a result of the interface configuration when you enter the command ipv6 address autoconfig default?
A. a static IPv6 default route pointing to the upstream DHCP server
B. a static IPv6 default route pointing to the upstream DHCP relay
C. a static IPv6 default route pointing to the upstream router
D. a temporary stateless address, formed from the EUI-64 bit address and the prefix from the route advertisement of the upstream router
Q172. Which three protocols support SSM? (Choose three.)
C. IGMP v3lite
Q173. Which two OSPF LSA types are flooded within the originating area? (Choose two.)
A. type 1, Router LSA
B. type 2, Network LSA
C. type 3, Network Summary LSA
D. type 4, ASBR Summary LSA
E. type 6, Group Membership LSA
F. type 9, Opaque LSA
OSPF relies on several types of Link State Advertisements (LSAs) to communicate link state information between neighbors. A brief review of the most applicable LSA types:
. Type 1 - Represents a router
. Type 2 - Represents the pseudonode (designated router) for a multiaccess link
. Type 3 - A network link summary (internal route)
. Type 4 - Represents an ASBR
. Type 5 - A route external to the OSPF domain
. Type 7 - Used in stub areas in place of a type 5 LSA LSA types 1 and 2 are found in all areas, and are never flooded outside of an area. They are only flooded within the area that they originated from.
Q174. DRAG DROP
Drag and drop the fragmentation characteristics on the left to the corresponding protocol on the right.
Q175. Which component of the BGP ORF can you use to permit and deny routing updates?
E. ORF type
Replace 400-101 exam price:
Q176. What are two benefits of Per-Tunnel QoS for DMVPN? (Choose two.)
A. The administrator can configure criteria that, when matched, can automatically set up QoS for each spoke as it comes online.
B. Traffic from each spoke to the hub can be regulated individually.
C. When traffic exceeds a configurable threshold, the spokes can automatically set up QoS with the hub.
D. The hub can send large packets to a spoke during allotted timeframes.
E. The hub can be regulated to prevent overloading small spokes.
Q177. Which two statements about a network running MPLS VPN with IS-IS IGP are true? (Choose two.)
A. IS-IS traffic engineering uses wide metric TLV type 135 with an up/down bit to define a leaked route.
B. IS-IS traffic engineering uses wide metric TLV type 128 with an internal/external bit and an up/down bit to define a leaked route.
C. IS-IS traffic engineering uses wide metric TLV type 130 with an internal/external bit and an up/down bit to define a leaked route.
D. If the IS-IS up/down bit is set to 1, the leaked route originated in the L1 area.
E. The MPLS VPN IS-IS core is inherently protected against IP-based attacks.
Q178. Refer to the exhibit.
Which BGP feature allows R1 to instruct R2 which prefixes it is allowed to advertise to R1?
A. route refresh
B. Prefix-Based Outbound Route Filtering
C. distribute lists
D. prefix lists
Q179. On a network using RIPng, the prefix field of a routing table entry has a value of 0:0:0:0:0:0:0:0. What does this value signify?
A. The next hop address is unknown.
B. The next hop address is a site-local address.
C. The neighboring router has IPv6 ND disabled.
D. The next hop address must be the originator of the route advertisement.
E. The associated route follows a default route out of the network.
Q180. Which topology allows the split-horizon rule to be safely disabled when using EIGRP?
A. full mesh
B. partial mesh
C. hub and spoke